Bunn DUAL GPR-DBC WITH SMART FUNNEL 41343 Manuel d'utilisateur

PROGRAMMING MANUALBUNN-O-MATIC CORPORATIONPOST OFFICE BOX 3227SPRINGFIELD, ILLINOIS 62708-3227PHONE: (217) 529-6601 FAX: (217) 529-6644 41343.

Page 10PROGRAMMING FUNCTIONS (cont.)% BYPASS XX (-) DONE (+)3 BATCHES DONE? NO YESSET PULSE BREW NO YESFULL1/21/4SET ALL3 BATCHE

Page 11PROGRAMMING FUNCTIONS (cont.)L BYPS OZ/M XX.X (-) DONE (+) R BYPS OZ/M XX.X (-) DONE (+)CALIBRATE FLOW? NO YESBREW C

Page 12PROGRAMMING FUNCTIONS - (cont.)2. Press DONE to proceed. The display should now read CHANGING UNITS!! WILL ERASE!! ... ALL PREVIOUSLY STORED RE

Page 13AUTO WARMER SHUT OFF (SETTING THE AUTO WARMER TO OFF OR A PROGRAMED TIME) This function allows the warmers on the brewer to be programed aut

Page 14FRESHNESS TIME This function activates a timer to provide a visual indication that the dispensed beverage has reached it's maximum hold t

Page 15ENABLE ENERGYSAVRThis function allows the operator to enable the ENERGY SAVINGS mode function and set the idle time. Once the set idle time has

Page 16MUST GRIND INTO FUNNEL FIRST (COFFEE NAME) SETUP COMPLETE BEGIN SETUP OF (COFFEE NAME) QUIT SETUP? YES USE LEFT SIDE ONLY INSERT FUNNEL WITH NE

Page 17PROGRAMMING THE BREWER (cont.)SET NEW RECIPE (cont.)8. Using (-) and (+), set the amount of brew water, in ounces, to be dispensed for that par

Page 18SET NEW RECIPES (cont.)PROGRAMMING THE BREWER (cont.)SET NEW RECIPE:Using a RECIPE CARD to load coffee names and brew settings into the Single/

Page 19DUALBREWERSPROGRAMMING THE BREWER (cont.)SET NEW RECIPES (cont.)SET NEW RECIPE:If not using a Smart Funnel (with a computer chip) and/or a G9-2

Page 241343 030912BUNN-O-MATIC COMMERCIAL PRODUCT WARRANTYBunn-O-Matic Corp. (“BUNN”) warrants equipment manufactured by it as follows:1) Airpots, the

Page 20PROGRAMMING FUNCTIONS - (cont.)REVIEW RECIPES/MODIFY RECIPES/SET UP NO NAME COFFEE FAVORS: This function has three parts. It allows the operat

Page 21PROGRAMMING FUNCTIONS - (cont.)BREW OZ (SETTING OR ADJUSTING BREW VOL-UMES) This function allows adjustment of the brew vol-umes for each bat

Page 22PROGRAMMING FUNCTIONS - (cont.)% BYPASS This function allows adjustment of the amount of water that bypasses the grounds. The number signi-fies

Page 23PROGRAMMING FUNCTIONS - (cont.)SET PULSE BREW: This function allows the operator to program the brewer to "pulse” the sprayhead flow on an

Page 24 NO-NAME LEFT, along with MODIFY, SHOW and NEXT (DUAL brewers).3. Press and release NEXT to advance to the desired coffee name to be modified.

Page 25SET PULSE BREW - MANUAL METHODNOTE: The procedure to enter the PULSE BREW function must be performed prior to following the steps listed belo

Page 26PROGRAMMING FUNCTIONS - (cont.)41343 043012DRIP TIME (now displayed on "non" funnel lock units as well) This function allows the set

Page 27COPY SETTINGS (NO NAME COFFEE SETTINGS ONLY) This function is used on DUAL brewers only to transfer all the brew settings from a NO NAME coffe

Page 28ENABLE ADS? This function allows the operator to choose whether or not to display the advertising message that was en-tered into the brewer wi

Page 29Procedure to set the sensitivity threshold of the refill circuit:NOTE: Make sure the water in the tank is touching the refill probe.1. Press and

Page 3TABLE OF CONTENTSGlossary ...

Page 30SPRAY OZ/M (DUAL BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the sprayhead. This is NOT u

Page 31BYPASS OZ/M (SINGLE BREWERS) This function allows the operator to view or to enter the actual flow rate coming out of the bypass nozzle. This

Page 32PROGRAMMING FUNCTIONS - (cont.)CALIBRATE FLOW?NO YESSPRAYHEAD CAL?NO YESCONTAINER READY?NO

Page 33PROGRAMMING FUNCTIONS - (cont.)Procedures to calibrate the bypass flow rate:1. Place a container, accurately graduated in ounces, and with a mi

Page 34PROGRAMMING FUNCTIONS - (cont.)BREW COUNTERS This function allows the operator to track the number of brew cycles completed. The number of bre

Page 35PROGRAMMING FUNCTIONS - (cont.)FUNNEL DETECT (optional) This function allows the operator to prevent the start of a brew cycle if a Smart Funn

Page 36PROGRAMMING FUNCTIONS - (cont.)TEST OUTPUTS?NO YESSERVICE TOOLS?NO YESLEFT BREW VALVEON NEXT OFFLEF

Page 37PROGRAMMING FUNCTIONS - (cont.)SERVICE TOOLS (cont.)6. Press and release YES. The display should read: BREW VALVE on SINGLE brewers. LEFT BRE

Page 38Procedures to test coil frequency:1. Place brew funnel(s) into rails of the brewer.2. Place a GPR beneath brew funnel(s).3. Press and hold u

Page 4GLOSSARYAD CARD: An assembly consisting of a computer chip (TAG) and an instruction label. Used for loading advertis-ing messages into the brewe

Page 5PROGRAMMING Using the menu-driven display on the front of the brewer, the operator has the ability to alter or modify various brewing paramete

Page 6MAIN SCREENREADY TO BREWWATER TEMP: 200° This screen will be shown when the brewer is ready for use. The screen displays the water temperature

Page 7PROGRAMMING THE BREWER (cont.)RECIPE PROGRAMING METHODS There are three methods of programming the vari-ous brewing parameters of the SINGLE/GP

Page 8LEVEL IPress upper right hidden switch for approximately 2 seconds, until the following screen appears.LEVEL IIPress upper right hidden switch

Page 941343 043012PROGRAMMING FUNCTIONS (cont.)Cycles thru right sideprogram constantsLEFT<-<-<-<-<-<-RIGHT NO Y