Bunn COMBO BREWER Manuel de service télécharger pdf (Page 13)

Page 13

40410 012814

PROGRAMMING - SMART WAVE COMBO

BREW VOLUME SET-UP:

NOTE: Maximum water on time is 5 minutes.

1. Press the "HIDDEN" switch until display reads C1. This represents the adjust mode "Brew Time" for the "A"

brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease time (-) or

"BREW B" to increase time (+).

2. Press and release "HIDDEN" switch until display reads C2. This represents the adjust mode "Brew Meter"

(Pulse Brew) for the "A" brew switch. The display will then change to (1-14). Brewer has 14 preset pulse brew

routines to choose from. Factory default is 1. With 14 being the maximum time. Press "BREW A" to decrease

(-) or "BREW B" to increase (+).

3. Press and release "HIDDEN" switch until display reads C3. This represents the adjust mode "Drip Out Time"

for the "A" brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease time

(-) or "BREW B" to increase time (+).

4. Press and release "HIDDEN" switch until display reads T1. This represents the adjust mode "Brew Time" for

the "A" brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease time

(-) or "BREW B" to increase time (+).

5. Press and release "HIDDEN" switch until display reads T2. This represents the adjust mode "Brew Meter"

(Pulse Brew) for the "B" brew switch. The display will then change to (1-14). Brewer has 14 preset pulse brew

routines to choose from. Factory default is 1. With 14 being the maximum time. Press "BREW A" to decrease

(-) or "BREW B" to increase (+).

6. Press and release "HIDDEN" switch until display reads T3. This represents the adjust mode "Drip Out Time"

for the "B" brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease time

(-) or "BREW B" to increase time (+).

7. Press and release "HIDDEN" switch until display reads T4. This represents the adjust mode "Dilution Time"

for the "B" brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease time

(-) or "BREW B" to increase time (+).

8. Press and release "HIDDEN" switch until display reads T5. This represents the adjust mode "Dilution Delay

Time" for the "B" brew switch. The display will then change to (minutes-seconds). Press "BREW A" to decrease

time (-) or "BREW B" to increase time (+). To have a quick dilution, set this time to zero.

NOTE: Advanced programming screens are same as standard Smart Wave.

Adjustment Default Min. Max. Increments

C1 = Brew switch "A" Brew time 2:35 0:26 5:00 1 second

C2 = Brew switch "A" Brew meter 1 1 14 1

C3 = Brew switch "A" Drip out time 0:30 0:05 5:00 5 seconds

T1 = Brew switch "B" Brew time 1:15 0:26 5:00 1 second

T2 = Brew switch "B" Brew meter 1 1 14 1

T3 = Brew switch "B" Drip out time 0:30 0:05 5:00 5 seconds

T4 = Brew switch "B" Dilution out time 1:20 0:05 5:00 5 seconds

T5 = Brew switch "B" Dilution Delay 3:30 0:00 5:00 5 seconds

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 22 23

Pas de commentaire

Bunn COMBO BREWER Manuel de service Page 13